Posts Tagged ‘android arduino’

Arduino WiFi Shield : JSON Parsing

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
#include ;
#include ;

char ssid[] = "Kazi-House"; // your network SSID (name)
char pass[] = "123456789"; // your network password
int keyIndex = 0; // your network key Index number (needed only for WEP)

int status = WL_IDLE_STATUS;

WiFiServer server(80);

void setup() {
//Initialize serial and wait for port to open:
Serial.begin(9600);

// check for the presence of the shield:
if (WiFi.status() == WL_NO_SHIELD) {
Serial.println("WiFi shield not present");
// don't continue:
while(true);
}

// attempt to connect to Wifi network:
while ( status != WL_CONNECTED) {
Serial.print("Attempting to connect to SSID: ");
Serial.println(ssid);
// Connect to WPA/WPA2 network.
// Change this line if using open or WEP network:
status = WiFi.begin(ssid, pass);

// wait 10 seconds for connection:
delay(10000);
}
server.begin();
// you're connected now, so print out the status:
printWifiStatus();
pinMode(45, OUTPUT);
pinMode(46, OUTPUT);
pinMode(47, OUTPUT);
pinMode(48, OUTPUT);
pinMode(49, OUTPUT);
pinMode(51, OUTPUT);
}

void loop() {
// listen for incoming clients
WiFiClient client = server.available();
if (client) {
//Serial.println("new client");
// an http request ends with a blank line
boolean currentLineIsBlank = true;
while (client.connected()) {
if (client.available()) {
char c = client.read();
//Serial.write(c);
if(c=='1'){
if(client.read() == '=') {
char onoff = client.read();
if( onoff == '1'){
Serial.println("Center Bulb On");
digitalWrite(45,HIGH);
}
else if(onoff == '0'){
Serial.println("Center Bulb Off");
digitalWrite(45,LOW);
}
}
}
else if(c=='2'){
if(client.read() == '=') {
char onoff = client.read();
if( onoff == '1'){
Serial.println("No Device 1 On");
digitalWrite(46,HIGH);
}
else if(onoff == '0'){
Serial.println("No Device 1 Off");
digitalWrite(46,LOW);
}
}
}
else if(c=='3'){
if(client.read() == '=') {
char onoff = client.read();
if( onoff == '1'){
Serial.println("BathRoom TubeLight On");
digitalWrite(47,HIGH);
}
else if(onoff == '0'){
Serial.println("BathRoom TubeLight Off");
digitalWrite(47,LOW);
}
}
}
else if(c=='4'){
if(client.read() == '=') {
char onoff = client.read();
if( onoff == '1'){
Serial.println("No Device 2 On");
digitalWrite(48,HIGH);
}
else if(onoff == '0'){
Serial.println("No Device 2 Off");
digitalWrite(48,LOW);
}
}
}
else if(c=='5'){
if(client.read() == '=') {
char onoff = client.read();
if( onoff == '1'){
Serial.println("Room TubeLight On");
digitalWrite(49,HIGH);
}
else if(onoff == '0'){
Serial.println("Room TubeLight Off");
digitalWrite(49,LOW);
}
}
}
else if(c=='6'){
if(client.read() == '=') {
char onoff = client.read();
if( onoff == '1'){
Serial.println("No Device 3 On");
digitalWrite(51,HIGH);
}
else if(onoff == '0'){
Serial.println("No Device 3 Off");
digitalWrite(51,LOW);
}
}
}
// if you've gotten to the end of the line (received a newline
// character) and the line is blank, the http request has ended,
// so you can send a reply
if (c == '\n' && currentLineIsBlank) {
// send a standard http response header
client.println("HTTP/1.1 200 OK");
client.println("Content-Type: text/html");
client.println("Connnection: close");
client.println();
break;
}
if (c == '\n') {
// you're starting a new line
currentLineIsBlank = true;
}
else if (c != '\r') {
// you've gotten a character on the current line
currentLineIsBlank = false;
}
}
}
// give the web browser time to receive the data
delay(1);
// close the connection:
client.stop();
//Serial.println("client disonnected");
}
}

void printWifiStatus() {
// print your WiFi shield's IP address:
IPAddress ip = WiFi.localIP();
Serial.print("IP Address: ");
Serial.println(ip);
}

Communication Mediums: Arduino WiFi, RN-42 Bluetooth, Netduino Ethernet

Hello, I have gotten my hands on couple of communication devices which could be used for android and Arduino/ Netduino communication, first RN-42 SMD bought from robotics.pk – link, Arduino WiFi Shield also bought from robotics.pk – link and third is Netduino it self which comes with Ethernet shield built-in, and Netduino is given to me by my teacher for educational purposes only, sad cant keep it.

Any ways lets start of with, RN-42 SMD is fairly cheap comparatively to others available for sale on spark fun  and is very easy to use you just need 4 connections VCC(3.3v),GND,RX and TX and you are done and by default RN-42 runs on 115200 braud rate, I found this to be very cheap and easy to use although for making connections on the smd, could be stressing, you would need small and steady hands, after making connections and connecting it to my Arduino Mega 2560, I used my serial Bluetooth android app and data transfer was done perfectly and fast, and range was acceptable, about 50 to 60 feet. it is perfect fit for short range, battery powered application.

Second device is WiFi Shield, which lets Arduino board connect to the internet using the 802.11 wireless specification and comes with a micro-SD card socket for saving of html pages and data logging,  we could either use the WiFi Shield as Server or Client and in my case I use it as a server, although Arduino cant process anything above HTML and JavaScript but we can do with these all so well, with WiFi Shield, we use Get and Post methods – (which I will explain in next post how?) to send and receive data from Arduino, from then on its same as serial monitor or Bluetooth. So from my android I send a request on the ip which is assigned to WiFi Shield through DHCP, request could be Get or Post and Arduino executes that request.

Arduino and WiFi Shield : Controlling my room lights from Kazi Murtaza on Vimeo.

Third device which is Netduino in-built Ethernet Shield, I have not gotten around to configure it yet, but will do it next. I feel the results will be same as Arduino WiFi Shield.

So in end I realized one thing, WiFi Shield is a bit buggy, sometimes requests in buffer of Arduino don’t really execute and if they do its 4-5 sec delay, I guess it takes time to process the request and its fairly new so needs a firmware update, so WiFi shield is not recommended for on second execution for example like WiFi controlled car, for such projects Bluetooth should be preferred, and for projects such as Home Automation and such WiFi is ideal.

 

 

things

My Jarvis

Jarvis, the one from iron man movie, Yes, Digital Life Assistance crazy idea for hobby project, right ? well we have seen many different kind’s of implementation’s in hope’s of achieving what that rich bastard has, but if we were to have it, we must first have platform to build upon, as far as I can see we need a system which is capable of achieving tasks in real world and virtual world, so to start off my first task is controlling the lights with Arduino, don’t worry I will be taking it slow. Idea, if it was not clear above,  idea is to use Arduino without spending a lot of money(very crucial) to control devices such as bulbs, fans and stuff,  I plan on using some sort of communication shield, When done it will send some MESSEAGE(not really clear on that) to Arduino, Arduino will move some relays and give me back a  response, toggling devices.

next post will be about requirements and basic concept of controlling a device through relay.